Weblink Mobile

Find answers to common installation issues with the WebLink mobile.
Post Reply
irelectronics
12Volt Specialist
Posts: 42
Joined: Sat Nov 21, 2015 1:39 pm
Location: Grunthal, Manitoba, Canada
Contact:

Weblink Mobile

Post by irelectronics » Fri Jun 03, 2016 8:20 pm

I have programmed HC remote starter with success using the Mobile weblink however I notice even with a PC or with this mobile Weblink that I have to pull the main power fuses for the HC in order for the weblink to detect the module. Is there going to be a fix for this where we wont have to disconnect power to the HC module in order to configure it?
Isaak Doerksen
Phone: 204-355-8464
IR Electronics
27061 PR216
Grunthal, MB
R0A0R0
Canada

User avatar
Murph
Site Admin
Posts: 7142
Joined: Sun Oct 23, 2011 8:35 pm

Re: Weblink Mobile

Post by Murph » Fri Jun 03, 2016 9:45 pm

You can't flash any module with 12v power attached to it. They are not designed to be flashed in the car.
Brian Murphy
MECP Advanced Certified Installer
ADS Tech Support
Automotive Data Solutions inc.
8400, Bougainville, Montreal, QC.
1-866-427-2999
support@idatalink.com

irelectronics
12Volt Specialist
Posts: 42
Joined: Sat Nov 21, 2015 1:39 pm
Location: Grunthal, Manitoba, Canada
Contact:

Re: Weblink Mobile

Post by irelectronics » Mon Jun 06, 2016 8:45 am

I understand that they need to be flashed outside the vehicle with the vehicle firmware. However I believe once the firmware has been programmed, you should be able to change remote start setting like how long you want engine to run or any other remote start functions with out removing remote starter or climbing under dash to connect to it.

Just a thought...
Isaak Doerksen
Phone: 204-355-8464
IR Electronics
27061 PR216
Grunthal, MB
R0A0R0
Canada

User avatar
Murph
Site Admin
Posts: 7142
Joined: Sun Oct 23, 2011 8:35 pm

Re: Weblink Mobile

Post by Murph » Mon Jun 06, 2016 8:54 am

Unfortunately, there is no way to change settings from a PC or Weblink Mobile without disconnecting power.
Brian Murphy
MECP Advanced Certified Installer
ADS Tech Support
Automotive Data Solutions inc.
8400, Bougainville, Montreal, QC.
1-866-427-2999
support@idatalink.com

Wombler
New User
Posts: 6
Joined: Sat Jun 04, 2016 8:40 pm

Re: Weblink Mobile

Post by Wombler » Mon Jun 06, 2016 8:17 pm

irelectronics wrote:I understand that they need to be flashed outside the vehicle with the vehicle firmware. However I believe once the firmware has been programmed, you should be able to change remote start setting like how long you want engine to run or any other remote start functions with out removing remote starter or climbing under dash to connect to it.

Just a thought...
I know you can use an OP500 option programmer for Compustar stuff to do exactly this. It just plugs in at the antenna and away you go...
However, not sure if they are compatible with the starters you are using?

User avatar
Murph
Site Admin
Posts: 7142
Joined: Sun Oct 23, 2011 8:35 pm

Re: Weblink Mobile

Post by Murph » Tue Jun 07, 2016 11:31 am

No the OP500 does not work with HC product.
Brian Murphy
MECP Advanced Certified Installer
ADS Tech Support
Automotive Data Solutions inc.
8400, Bougainville, Montreal, QC.
1-866-427-2999
support@idatalink.com

Post Reply

Return to “Weblink Mobile”